SCSI kontrollery NCR5380 i NCR53c400 vypuskayutsya v dvuh modifikaciyah:
  port ili memory mapped. Esli Vy imeete eti karty, Vam sleduet opredelit'
  tip mappirovaniya i ustanovit' ego. Bol'shinstvo kart, Trantor T130B,
  ispol'zuyut port mapped rezhim.

        NCR53c7,8xx SCSI support.	CONFIG_SCSI_NCR53C7xx
CONFIG_SCSI_NCR53C7xx
  Dannyj drajver podderzhivaet semesjstvo SCSI kontrollerov 53c7 i 8xx NCR.
  Ne putajte iz s kontrollerami NCR 5380. Bolee podrobnuyu inforomaciyu
  Vy mozhete najti v sekcii 3.8 SCSI-HOWTO, dostupnyj cherez ftp
  (user: anonymous) na sunsite.unc.edu:/pub/Linux/docs/HOWTO,
  ili v fajle drivers/scsi/README.aic7xxx.
  Esli drajver ne rabotaet, to Vy mozhete popytat'sya izmenit'
  nekotorye ustanovki ya fajle drivers/scsi/53c7,8xx.h.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.

        always negotiate synchronous transfers.	CONFIG_SCSI_NCR53C7xx_sync
CONFIG_SCSI_NCR53C7xx_sync
  Vklyuchaet rezhim sinhronnoj peredachi. |to neplohaya vozmozhnost', no
  imeejte v vidu, chto sushchestvuyut SCSI adaptery, neverno realizuyut
  etot rezhim. Tak chto esli ne uvereny - otvet'te N.

        allow FAST-SCSI [10MHz].	CONFIG_SCSI_NCR53C7xx_FAST
CONFIG_SCSI_NCR53C7xx_FAST
  |tot kod vklyuchaet vozmozhnost' peredachi v rezhime 10MHz FAST-SCSI
  na Vashem adaptore. Nekotorye sistemy imeyut problemy s etim
  rezhimom, tak chto esli ne uvereny - otvet'te N.

        allow DISCONNECT.	CONFIG_SCSI_NCR53C7xx_DISCONNECT
CONFIG_SCSI_NCR53C7xx_DISCONNECT
  |tot drajver vklyuchaet rezhim rassoedineniya/peresoedineniya
  (disconnect/reconnect) na kontrollerah NCR SCSI. |to byvaet polezno
  v sluchae, esli Vy ispol'zuete odnovremenno bystrye i medlennye
  SCSI ustrojstva. V etom rezhime medlennye ustrojstva ne budut
  blokirovat' SCSI adapter vo vremya vypolneniya zaprosa, chto
  pozvolyaet odnovremenno ispol'zovat', naprimer, SCSI disk,
  SCSI lentu ili SCSI CDROM. Pravda nekotorye ustrojstva nekorrektno
  rabotayut v etom rezhime, zaveshivaya Vash SCSI adapter. Tak chto esli
  Vy ne uvereny - ne otvechajte Y.

        NCR53C8XX SCSI support.	CONFIG_SCSI_NCR53C8XX
CONFIG_SCSI_NCR53C8XX
  |to NCR drajver dlya semestva PCI-SCSI kontrollerov NCR53C8XX
  portirovan iz BSD. On podderzhivaet proverku chetnosti, ochered' komand,
  bystryj rezhim peredachi SCSI II do 10 MB/s s "uzkimi" (narrow)
  ustrojstvami i do 20 MB/s s "shirokimi" (wide) ustrojstvami.
  |tot drajver ottestirovan dlya linux/i386 i poka neottestirovan dlya
  linux/Alpha. Esli Vy namerevaetes' ispol'zovat' etot drajver dlya
  linux/Alpha, poprobujte ego snachala v rezhime tol'ko na chtenie
  (read-only) ili montirovat' v rezhime (read-only). Memory mapped
  rezhim v nastoyashchee vremya ne podderzhivaetsya. Pochitajte fajl
  drivers/scsi/README.ncr53c8xx dlya dopolnitel'noj inormacii.

        force normal IO.	CONFIG_SCSI_NCR53C8XX_IOMAPPED
CONFIG_SCSI_NCR53C8XX_IOMAPPED
  Pod linux/Alpha podderzhivaetsya tol'ko normal'nyj rezhim vvod/vyvoda.
  Pod linux/i386, etot rezhim zastavlyaet drajver ispol'zovat'
  normal'nyj rezhim vvoda/vyvoda. Memory mapped rezhim vvoda/vyvoda
  imeet men'shie zaderzhki, chem normal'nyj rezhim. Vo vremya inicializacii
  drajver snachala pytaetsya ispol'zovat' "memory mapped" rezhim
  vvoda/vyvoda. Esli etot rezhim ne opredelyaetsya, ispol'zuetsya
  normal'nyj rezhim vvoda/vyvoda. Odnako, inogda rezhim "memory mapped"
  rabotaet nekorrektno. V etom sluchae Vam sleduet otvetit' N.
  A obychnyj otvet - Y.

        not allow targets to disconnect.	CONFIG_SCSI_NCR53C8XX_NO_DISCONNECT
CONFIG_SCSI_NCR53C8XX_NO_DISCONNECT
  |tot rezhim sleduet ispol'zovat' tol'ko v tomi sluchae, esli Vy
  podozrevaete, chto nekotorye Vashi ustrojstva nekorrektno podderzhivayut
  rezhim rassoedineniya. V etom sluchae sleduet otvetit' Y. V obshchem sluchae
  vklyuchat' etot rezhim ne rekomenduetsya, esli Vy imeete bolee 1-go SCSI
  ustrojstva. Obychnyj otvet - N.

        enable tagged command queuing.	CONFIG_SCSI_NCR53C8XX_TAGGED_QUEUE
CONFIG_SCSI_NCR53C8XX_TAGGED_QUEUE
  |tot parametr pozvolyaet Vam vklyuchit' rezhim ocheredi komand vo vremya
  raskrutki yadra. Nekotorye ustrojstva nekorrektno ispol'zuyut etot
  rezhim. V etom sluchae celesoobrazno otvetit' N na etot vopros i
  ispol'zovat' upravlyayushchuyu komandu settegs posle raskrutki yadra:
      echo "settags 2 4" >/proc/scsi/ncr53c8xx/0
  chto zastavit drajver ispol'zovat' do 4-h konkuriruyushchih komand dlya
  ustrojstva 2 0-go kontrollera.
  Pochitajte fajl drivers/scsi/README.ncr53c8xx dlya dopolnitel'noj
  informacii.
  PREDUPREZHDENIE: etot rezhim trebuet ustanovki rezhima razresheniya
  rassoedineniya dlya ustrojstva.
  Obychnyj otvet - Y.

        force asynchronous transfer mode.	CONFIG_SCSI_NCR53C8XX_FORCE_ASYNCHRONOUS
CONFIG_SCSI_NCR53C8XX_FORCE_ASYNCHRONOUS
  |tot rezhim pozvolyaet Vam ustanovit' rezhim asinhronnoj peredachi dlya
  vseh SCSI ustrojstv vo vremya raskrutki yadra. Ustanovit' rezhim
  sinhronnoj peredachi posle etogo Vy mozhete komandoj:
     echo "setsync 2 25" >/proc/scsi/ncr53c8xx/0
  kotoraya ustanovit period 25 ns (10MB/sec) dlya ustrojstva 2 0-go
  kontrollera (dlya dopolnitel'noj informacii pochitajte fajl
  drivers/scsi/README.ncr53c8xx).
  Obychnyj otvet - N.

        force synchronous negotiation.	CONFIG_SCSI_NCR53C8XX_FORCE_SYNC_NEGO
CONFIG_SCSI_NCR53C8XX_FORCE_SYNC_NEGO
  Nekotorye SCSI-2 ustrojstva podderzhivayut rezhim sihronnoj peredachi,
  no ne soobshchayut ob etom v 7-m bajte pri zaprose.
  Otvet'te Y esli Vy podozrevaete chto Vyshi ustrojstva imeyut etot
  nedostatok. Obychnyj otvet - N.

        disable master parity checking.	CONFIG_SCSI_NCR53C8XX_DISABLE_MPARITY_CHECK
CONFIG_SCSI_NCR53C8XX_DISABLE_MPARITY_CHECK
  Nekotorye ustrojstva imeyut odnokratnye problemy s chetnost'yu vo vremya
  osnovnogo cikla (master cycles) na shine PCI. Otvet'te Y, esli imeete
  etu problemu. Obychnyj otvet - N.

        disable scsi parity checking.	CONFIG_SCSI_NCR53C8XX_DISABLE_PARITY_CHECK
CONFIG_SCSI_NCR53C8XX_DISABLE_PARITY_CHECK
  Proverka chetnosti na shine SCSI - eto ssitemnaya opciya. Esli odno
  ustrojstvo proveryaet chetnosti, to i vse ostal'nye ustrojstva dolzhny
  generirovat' bit chetnosti. Odnako bit chetnosti mozhet ignorirovat'sya
  SCSI ustrojstvom. Otvet'te Y, esli Vy znaete, chto Vy delaete.
  Obychnyj otvet - N.

        Always IN2000 SCSI support.	CONFIG_SCSI_IN2000
CONFIG_SCSI_IN2000
  |tot drajver podderzhivaet Always IN2000 ISA bus SCSI host adapter.
  Dopolnitel'nuyu informaciyu Vy mozhete najti v fajle
  drivers/scsi/in2000.readme. Esli drajver ne rabotaet, Vam sleduet
  izmenit' pereklyuchateli (jumpers) dlya IRQ i adresa.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.

        PAS16 SCSI support.	CONFIG_SCSI_PAS16
CONFIG_SCSI_PAS16
  Drajver podderzhivaet PAS16 SCSI host adapter.
  Ego nastrojka opisana v sekcii 3.10 dokumenta SCSI-HOWTO, dostupnogo
  cherez (user: anonymous) na sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  Esli on ne rabotaet, poprobujte izmenit' nastrojki v fajle
  drivers/scsi/pas16.h.

        Qlogic FAS SCSI support.	CONFIG_SCSI_QLOGIC_FAS
CONFIG_SCSI_QLOGIC_FAS
  |tot drajver podderzhivaet tol'ko ISA, VLB i PCMCIA versii Qlogic
  FastSCSI! kart i takzhe drugie karty, osnovannye na mikrosheme
  FASXX (vklyuchaya karty Control Concepts SCSI/IDE/SIO/PIO/FDC). On
  NE PODDERZHIVAET PCI versiyu etih kart. Versiya PCI podderzhivaetsya
  drajverom Qlogic ISP. Informaciya ob etom drajvere soderzhitsya v
  fajle drivers/scsi/README.qlogicfas.
  Vam takzhe sleduet pochitat' SCSI-HOWTO, dostupnoe cherez ftp
  (user: anonymous) na sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.

        Qlogic ISP SCSI support (EXPERIMENTAL).	CONFIG_SCSI_QLOGIC_ISP
CONFIG_SCSI_QLOGIC_ISP
  |tot drajver rabotaet dlya vseh QLogic PCI SCSI host adapterov
  (IQ-PCI, IQ-PCI-10, IQ_PCI-D) za isklyucheniem karty PCI-basic.
  (Poslednij podderzhivaetsya drajverom "AM53/79C974 PCI SCSI").
  Esli Vy otvetite Y, ne zabud'te vklyuchit' podderzhku "PCI BIOS support".
  Informaciya ob etom drajvere soderzhitsya v
  fajle drivers/scsi/README.qlogicisp.
  Vam takzhe sleduet pochitat' SCSI-HOWTO, dostupnyj cherez ftp
  (user: anonymous) na sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.

        Seagate ST-02 and Future Domain TMC-8xx SCSI support.	CONFIG_SCSI_SEAGATE
CONFIG_SCSI_SEAGATE
  |to 8-mi bitnj SCSI-kontroller. ST-01 takzhe podderzhivaetsya etim
  drajverom. Bolee podrobno etot drajver opisan v SCSI-HOWTO,
  dostupnyj cherez ftp   (user: anonymous) na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  Esli on ne rabotaet, Vy mozhete poprobovat' izmenit' ustanovki
  v fajle drivers/scsi/seagate.h.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.

        Trantor T128/T128F/T228 SCSI support.	CONFIG_SCSI_T128
CONFIG_SCSI_T128
  |tot drajver podderzhivaet T128/T128F/T228 SCSI host adaptery.
  Ego nastrojka opisana v sekcii 3.12 dokumenta SCSI-HOWTO, dostupnogo
  cherez (user: anonymous) na sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  Esli on ne rabotaet, poprobujte izmenit' nastrojki v fajle
  drivers/scsi/t128.h.
  Imejte v vidu, chto firma Trantor byla nedavno kuplena firmoj Adaptec,
  tak chto platy firmy Trantor mogut prodavat'sya pod markoj Adaptec.

        UltraStor SCSI support.	CONFIG_SCSI_ULTRASTOR
CONFIG_SCSI_ULTRASTOR
  |tot drajver podderzhivaet semejstvo adapterov UltraStor 14F, 24F i
  34F SCSI-2.
  Ego nastrojka opisana v sekcii 3.12 dokumenta SCSI-HOWTO, dostupnogo
  cherez (user: anonymous) na sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  Esli on ne rabotaet, poprobujte izmenit' nastrojki v fajle
  drivers/scsi/ultrastor.h.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.
  Zamet'te, chto sushchestvuet drugoj drajver dlya etih ustrojstv:
  "UltraStor 14F/34F support", opisannyj vyshe. Vy dolzhny vybrat'
  odin iz nih.

        7000FASST SCSI support.	CONFIG_SCSI_7000FASST
CONFIG_SCSI_7000FASST
  |tot drajver podderzhivaet Western Digital 7000 SCSI host adapter.
  Nemnogo informacii Vy mozhete izvlecht iz fajla drivers/scsi/wd7000.c.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.

        EATA ISA/EISA (DPT PM2011/021/012/022/122/322) support.	CONFIG_SCSI_EATA
CONFIG_SCSI_EATA
  |tot drajver podderzhivaet semejstvo DPT SCSI host adapterov, takih
  kak   PM2011B/9X, PM2021A/9X, PM2012A, PM1012B, PM2022A/9X, PM2122A/9X
  i PM2322A/9X. Zamet'te, chto PM2001 etim drajverom ne podderzhivaetsya.
  Dopolnitel'nuyu informaciyu Vy mozhete pochitat' v fajle
  drivers/scsi/eata.c i v SCSI-HOWTO, dostupnogo po ftp (user: anonymous)
  na sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.

        NCR53c406a SCSI support.	CONFIG_SCSI_NCR53C406A
CONFIG_SCSI_NCR53C406A
  |tot drajver podderzhivaet NCR53c406a SCSI host adapter. Dlya
  ustanovki konfiguracionnyh parametrov posmotrite ishodnyj fajl
  drivers/scsi/NCR53c406.c.
  Dopolnitel'nuyu informaciyu Vy mozhete pochitat' v fajle
  drivers/scsi/eata.c i v SCSI-HOWTO, dostupnogo po ftp (user: anonymous)
  na sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.

        AM53/79C974 PCI SCSI support.	CONFIG_SCSI_AM53C974
CONFIG_SCSI_AM53C974
  |tot drajver podderzhivaet AM53/79C974 SCSI host adapter.
  Dopolnitel'nuyu informaciyu Vy mozhete pochitat' v fajle
  drivers/scsi/README.AM53C974 i v SCSI-HOWTO, dostupnogo po ftp
  (user: anonymous) na sunsite.unc.edu:/pub/Linux/docs/HOWTO.

        IOMEGA Parallel Port ZIP drive SCSI support.	CONFIG_SCSI_PPA
CONFIG_SCSI_PPA
  |tot drajver podderzhivaet IOMEGA ZIP drajv, rabotayushchij cherez
  parallel'nyj port (100Mb floppi-diski).
  Dopolnitel'nuyu informaciyu Vy mozhete pochitat' v fajle
  drivers/scsi/README.ppa. i v SCSI-HOWTO, dostupnogo po ftp
  (user: anonymous) na sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.
  Esli Vy planiruete ispol'zovat' lyuboj iz dvuh imeyushchihsya u Vas v
  nalichii parallel'nyh portov dlya ZIP drajva, parallel'nyj printer
  ili PLIP soedinenie na odnom i tom zhe parallel'nom portu, to Vam
  sleduet otkompilirovat' etot drajver kak modul'nyj i vklyuchat' ego
  po neobhodimosti.
  Zamet'te, chto esli Vy imeete SCSI versiyu ZIP drajva, to Vam
  neobhodimo otvetit' N. |tot drajv podderzhivaetsya avtomaticheski
  pri vklyuchenii rezhima "SCSI disk support", opisannogo vyshe.

        Network device support?.	CONFIG_NETDEVICES
CONFIG_NETDEVICES
  Vy mozhete otvetit' N, esli ne sobiraetes' svyazyvat'sya ni s kakim
  komp'yuterom ili vse vashi soedineniya ogranichivayutsya UUCP soedineniem
  (UUCP - protokol dlya peredachi zadanij (pochty ili novostej) mezhdu
  UNIX-mashinami po telefonnym liniyam, chitajte UUCP-HOWTO, dostupnyj
  cherez ftp (user:anonymous) na sunsite.unc.edu:/pub/Linux/docs/HOWTO),
  ili udalennym vhodom na drugoj komp'yuter ili BBS ili term (term -
  programma, dayushchaya Vam pochta polnoe Intrenet-soedinenie pri nalichii
  u Vas gostevogo vhoda na odnoj iz Internet UNIX-mashine. CHitajte
  Term-HOWTO). Vam sleduet otvetit' Y, esli Vash komp'yuter imeet
  setevuyu kartu i Vy sobiraetes' ee ispol'zovat' (opredelite ee tip,
  tak kak Vy dolzhny podklyuchit' dlya nee drajver, chitajte
  Multiple-Ethernet-mini-HOWTO, dostupnyj cherez ftp (user:anonymous)
  na sunsite.unc.edu:/pub/Linux/docs/HOWTO/mini) ili Vy planiruete
  ispol'zovat' SLIP (Serial Line Internet Protocol - protokol dlya
  peredachi IP-paketov cherez telefonnye ili null-modemnye kabeli),
  CSLIP (compressed SLIP - protokol SLIP s szhatiem), PPP (novyj
  i luchshij variant SLIP'a), PLIP (protokol,ispol'zuemyj dlya peredachi
  IP-paketov cherez parallel'nye porty),
  AX25/KISS (protokol dlya peredachi IP-paketov po radio linii).
  Dlya bolee polnoj informacii pochitajte dokument NET-2-HOWTO.
  Vozmozhno, Vam sleduet pochitat' otlichnuyu knigu "Network Administrator's
  Guide" Olafa Kirha, kotoruyu Vy mozhete najti na
  sunsite.unc.edu:/pub/Linux/docs/LDP.
  Esli ne uvereny - otvet'te Y.

        Ethernet.	CONFIG_NET_ETHERNET
CONFIG_NET_ETHERNET
  Ethernet - naibolee obshchij protokol, ispol'zuemyj v lokal'nyh setyah
  (LAN). Sushchestvuyut tipy Ethernet 10-base-2, 10-base-T ili
  100-base-<chto-libo>. Esli Vasha Linux mashina bvttn ethernet kartu
  i Vy planiruete podklyuchit'sya k lokal'noj seti, otvet'te Y
  i pochitajte Ethernet-HOWTO, dostupnyj cherez ftp (user: anonymous)
  na sunsite.unc.edu:/pub/Linux/docs/HOWTO. Zametim, chto otvet na etot
  vopros ne vyzyvaet napryamuyu vklyuchenie koda v yadro. Otvetiv N,
  Vy vsego lish' obojdete voprosy, svyazannye s podklyucheniem drajverov
  ethernet kart.  Esli ne uvereny - otvet'te N.

        Dummy net driver support.	CONFIG_DUMMY
CONFIG_DUMMY
  Dannoe ustrojstvo predstavlyaet soboj "musornuyu korzinu bitov"
  (tak kak dannye peredannye na nego predayutsya zabveniyu) s zadannym
  IP adresom. V obshchem sluchae eto delaetsya dlya togo, chtoby sdelat'
  vremenno neaktivnyj Vash SLIP adres real'nym dlya Vashih lokal'nyh
  programm. Esli Vy ispol'zuete SLIP ili PPP, Vam sleduet vklyuchit'
  etot rezhim. Pochitajte ob etom v knige Network Administrator's Guide,
  dostupnuyu po ftp (user: anonymous) s sunsite.unc.edu:/pub/Linux/docs/LDP.
  Tak kak dannaya vozmozhnost' predlagaet krasivoe reshenie, po umolchaniyu ona
  vklyuchena. Ona prkticheski ne uvelichivaet vashe yadro.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.
  Esli Vy planiruete ispol'zovat' bolee odnogo dummy ustrojstva
  odnovremenno, Vam sleduet otkompilirovat' drajver kak modul'nyj.

        SLIP (serial line) support.	CONFIG_SLIP
CONFIG_SLIP
  Otvet'te Y, Esli Vy planiruete ispol'zovat' SLIP ili CSLIP
  (kompressirovannyj SLIP) dlya soedineniya s Vashim Internet
  provajderom, ili soedineniya k drugij UNIX IP-set'yu ili esli Vy
  sobiraete prevratit' Vashu Linux-mashinu v SLIP/CSLIP server dlya
  podklyuchenii klientov po vydelennym ili komutiruemym liniyam.
  SLIP (Serial Line Internet Protocol - protokol dlya peredachi
  IP-paketov cherez telefonnye ili null-modemnye kabeli.
  Obychno, Vash Internet provajder dolzhen podderzhivat' SLIP
  dlya togo, chtoby Vy mogli im vospol'zovat'sya, no v nastoyashchee
  vremya sushchestvuet SLIP emulyator, nazyvaemyj SLiRP (dostupnyj cherez
  ftp (user: anonymous) iz
  sunsite.unc.edu:/pub/Linux/system/Network/serial/), kotoryj pozvolyaet
  Vam ispol'zovat' SLIP cherez mehanizm obychnogo udalennogo vhoda na
  mashinu IP provajdera. Esli Vy planiruete ispol'zovat' SLiRP,
  ne zabud'te takzhe vklyuchit' rezhim CSLIP, opisannyj nizhe.
  Dokument NET-2-HOWTO, dostupnyj na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO, opisyvaet kak nastraivat'
  SLIP. Zamet'te, chto Vam ne nuzhen etot rezhim, esli vy ispol'zuete
  term (programma, dayushchaya Vam pochta polnoe Intrenet-soedinenie pri
  nalichii u Vas gostevogo vhoda na odnoj iz Internet UNIX-mashine.
  CHitajte Term-HOWTO). Dannyj drajver uvelichit Vashe yadro na 4KB.
  Esli ne uvereny - otvechajte N.
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.

        CSLIP compressed headers.	CONFIG_SLIP_COMPRESSED
CONFIG_SLIP_COMPRESSED
  |tot protokol rabotaet bystree, chem SLIP, tak kak ispol'zuet
  kompressiyu zagolovkov IP-paketov (no ne samih dannyh), no on dolzhen
  dolzhen podderzhivat'sya na oboih storonah soedineniya. Tak chto, pered tem
  kak otvechat' Y, sprosite Vashego Internet provajdera. Esli planiruete
  ispol'zovat' SLiRP, SLIP emulyator  (dostupnyj cherez   ftp (user: anonymous)
  iz sunsite.unc.edu:/pub/Linux/system/Network/serial/), kotoryj pozvolyaet
  Vam ispol'zovat' SLIP cherez mehanizm obychnogo udalennogo vhoda na
  mashinu IP provajdera, to Vam neobhodimo otvetit' Y. NET-2-HOWTO,
  dostupnyj cherez ftp (user: anonymous) na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO, ob'yasnit kak nastroit'
  CSLIP. On prakticheski ne uvelichit Vashe yadro.

        Keepalive and linefill.	CONFIG_SLIP_SMART
CONFIG_SLIP_SMART
  Dannyj drajver dopolnyaet dopolnitel'nye vozmozhnosti po kontrolyu
  zapolnennosti i sohrannosti IP kanala, ispol'zuemyj v setyah RELCOM.
  Ideal'nyj rezhim dlya slabyh analogovyh linij.

        Six bit SLIP encapsulation.	CONFIG_SLIP_MODE_SLIP6
CONFIG_SLIP_MODE_SLIP6
  Esli Vam, sluchajno, neobhodimo imet' IP cherez "vrazheskie" serijnyj
  seti, ne peredayushchie vse kontrol-simvoly ili 7-bitnye linii.
  Otvetiv Y, Vy smozhete dobavit' k SLIP-protokolu dopolnitel'nyj
  rezhim - "slip6". V etom rezhime SLIP posylaet tol'ko ASCII-simvoly
  cherez serijnye linii. Estestvenno, eto rezhim dolzhen podderzhivat'sya
  na oboih storonah soedineniya. |tot rezhim polezen, naprimer, dlya
  raboty po IP cherez fsinhronnyj port Camtec JNT Pad. Esli ne uvereny,
  otvechajte N.

        Radio network interfaces.	CONFIG_NET_RADIO
CONFIG_NET_RADIO
  Interfejs po radiokanalam. On vklyuchaet dyubitel'skoe radio (AX.25),
  podderzhku besprovodnyh Ethernet i drugih sistem. Zametim, chto otvet
  na etot vopros ne vyzyvaet napryamuyu vklyuchenie koda v yadro. Otvetiv N,
  Vy vsego lish' obojdete voprosy, svyazannye s podklyucheniem drajverov
  radiokart. Neskol'ko drajverom urovnya pol'zovatel'skogo processa,
  ne trebuyushchie podderzhki na urovne yadra dostupny cherez ftp
  ftp (user: anonymous) na shadow.cabi.net. Esli neuvereny -
  otvechajte N.

        PPP (point-to-point) support.	CONFIG_PPP
CONFIG_PPP
  PPP (Point to Point Protocol - protokol tochka-tochka) novyj i luchshij
  protokol, chem SLIP. On sluzhit toj zhe celi - peredachi IP-paketov po
  telefonnym ili null-modemnym liniyam. Vyyasnite u svoego IP provajdera,
  podderzhivaet li on etot protokol, v protivnom sluchae Vy ne smozhete
  ego ispol'zovat' (v tom sluchae esli ne imeete SLiRP - programmy
  emulyacii PPP-protokola cherez obychnyj udalennyj vhod - Vy mozhete
  poluchit' etu programmu cherez ftp (user:anonymous) iz
  sunsite.unc.edu:/pub/Linux/system/Network/serial/).
  Dlya ispol'zovaniya PPP, Vam neobhodima programma, nazyvaemaya pppd,
  kak opisano v Documentation/networking/ppp.txt i v PPP-HOWTO,
  dostupnyj iz  sunsite.unc.edu:/pub/Linux/docs/HOWTO. Zamet'te,
  chto Vam ne nuzhen etot rezhim, esli Vy planiruete ispol'zovat' tol'ko
  term - programma, dayushchaya Vam pochta polnoe Intrenet-soedinenie pri
  nalichii u Vas gostevogo vhoda na odnoj iz Internet UNIX-mashine.
  CHitajte Term-HOWTO. PPP drajver uvelichivaet Vashe yadro na 16KB.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy vyshe vybrali rezhim "Version information on all symbols",
  to Vy ne smozhete vklyuchit' PPP drajver pryamo v yadro, mozhno ego
  vklyuchit' tol'ko kak modul'nyj. Esli Vy zhelaete otkompilirovat'
  ego kak modul'nyj drajver - otvet'te M i pochitajte fajly
  Documentation/modules.txt i Documentation/networking/net-modules.txt.
  Zametim, chto nezavisimo ot rezhima raboty PPP-drajvera (modul'nyj
  ili vklyuchennyj v yadro), kod BSD compression (ispol'zuemyj dlya
  szhatiya IP-paketov po serijnym liniyam) mozhet byt' otkompilirovan
  tol'ko kak modul'nyj. |tot fajl nazyvaetsya bsd_comp.o i avtomaticheski
  kompiliruetsya v direktorij modul'nyh drajverov posle sborki modulej
  komandoj "make modules". Esli neuvereny - otvet'te N.

        16 channels instead of 4.	CONFIG_PPP_LOTS
CONFIG_PPP_LOTS
  Otvetiv Y, vy smozhete ispol'zovat' odnovremenno do 16-ti
  (vmesto 4-x) odnovremennyh PPP-soedinenij. |to neobhodimo v sluchae
  ispol'zovaniya Vashej Linux-mashiny kak dial-in PPP server.
  V bol'shinstve sluchaev etot rezhim ne nuzhen.

        STRIP (Starmode Radio IP) support.	CONFIG_STRIP
CONFIG_STRIP
  Otvet'te Y, esli ispol'zuete Metricom radio i planiruete ispol'zovat'
  Starmode Radio IP. STRIP - eto radio protokol, razrabotannyj dlya
  prekta MosquitoNet (http://mosquitonet.stanford.edu/) dlya peredachi
  Internet paketov, ispol'zuya Metricom radios. Metricom radios -
  eto nebol'shoj, batarejnyj peredatchik, rabotayushchij na skorostyah
  100kbit/sec i razmerami, blizkimi s sotovym telefonom. (Vy mozhet byt'
  slyshali o nih kak o Metricom modemah, no my izbegaem termina modem,
  chtoby ne putat' ih s obychnymi modemami, podklyuchaemymi po telefonnoj
  seti). Vy mozhete ispol'zovat' STRIP na lyuboj Linux miashine s serijnym
  portom, hotya on naibolee polezen na Laptop'ah. Esli Vy planiruete
  ispol'zovat' Metricom radio v buduyushchem, net prichin ne otvetit' Y.
  Pravda yadro budet chut' bol'she.

        WIC (Radio IP bridge).	CONFIG_WIC
CONFIG_WIC
  Dannyj drajver podderzhivaet WIC parallel port radio bridge. Esli Vy
  ne imeete etogo ustrojstva - otvet'te N.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.

        Z8530 SCC kiss emulation driver for AX.25.	CONFIG_SCC
CONFIG_SCC
  |ta karta ispol'zuetsya dlya soedineniya Vyshej Linux mashiny k
  lyubitel'skomu radio. Esli Vy zhelaete ispol'zovat' etot rezhim,
  pochitajte dokumentaciyu Documentation/networking/z8530drv.txt i
  HAM-HOWTO, dostupnyj cherez ftp (user: anonymous) na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.

        BAYCOM ser12 and par96 kiss emulation driver for AX.25.	CONFIG_BAYCOM
CONFIG_BAYCOM
  |ksperemental'nyj drajver dlya Baycom modemov, rabotayushchih po kanalam
  lyubitel'skogo radio, kotorye podsoedinyaetsya libo k serijnomu libo k
  parallel'nomu portu. Drajver podderzhivaet ustrojstva ser12 i par96.
  Dlya konfiguracii drajvera ispol'zujte programmu setbaycom, dostupnuyu
  iz http://www.ife.ee.ethz.ch/~sailer/ham/ham.html#lnxbay Informaciyu
  po modemu Vy mozhete najti na http://www.baycom.de i v fajle
  drivers/char/README.baycom.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  (chto bolee predpochtitel'no) otvet'te M i pochitajte dokumentaciyu
  po modul'nym drajveram v fajle Documentation/modules.txt.

        PLIP (parallel port) support.	CONFIG_PLIP
CONFIG_PLIP
  PLIP (Parallel Line Internet Protocol - Internet protokol po
  parallel'nomu portu) ispol'zuetsya dlya sozdaniya minisetej, sostoyashchih
  iz dvuh (rezhe bolee) lokal'nyh mashin. Parallel'nye porty
  (25-shtyr'kovyj konnektory) soedinyayutsya "null printer" ili
  "Turbo Laplink" kabelem, kotoryj mozhet peredavat' 4 bita odnovremenno,
  ili ispol'zovat' special'nyj kabel' (raspajku etogo kabelya Vy mozhete
  najti v fajlah drivers/net/README1.PLIP i drivers/net/README2.PLIP)
  dlya portov s podderzhkoj dvustoronnej peredachi (bidirectional).
  V etom rezhime vozmozhna peredacha odnovremenno 8-mi bit. Dlina etogo
  kabelya mozhet dostigat' 15 metrov. Rezhim PLIP mozhno ispol'zovat' takzhe
  dlya soedineniya s DOS/Windows mashinami pri installyacii na nih
  programmnogo obespecheniya, podderzhivayushchego PLIP - naprimer Crynwr PLIP
  paketnyj drajver ili winsock or NCSA's telnet. Esli Vy zhelaete
  ispol'zovat' etot rezhim, otvet'te Y i pochitajte PLIP mini-HOWTO,
  dostupnyj cherez ftp (user: anonymous) na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO/mini, a takzhe NET-2-HOWTO na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO. Zamet'te, chto PLIP protokol
  izmenilsya i etot PLIP drjver ne budet rabotat' sovmestno s PLIP
  drajverom Linux versij 1.0.x. |tot drajver uvelichivaet yadro na 8KB.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  otvet'te M i pochitajte dokumentaciyu po modul'nym drajveram v
  fajle Documentation/modules.txt.
  Esli Vy zhelaete ispol'zovat' kak parallel'nyj printer, tak i PLIP,
  Vy mozhete vybrat' dva varianta:
  1) Esli printer i PLIP ispol'zuyut odin i tot zhe port (chto chashche vsego
  ya byvaet), to luchshe vsego otkompilirovat' oba drajvera kak modul'nye
  i vklyuchat' ih v yadro i udalyat' v sluchae neobhodimosti.
  2) Pri ispol'zovanii razlichnyh parallel'nyh portov dlya printera i
  PLIP kabelya, Vy mozhete skazat' Y dlya drajvera printera i ukazat'
  neobhodimyj adres parallel'nogo porta dlya printera vo vremya zagruzki
  yadra cherez parametr lp (smotrite dokumentaciyu na Vash nachal'nyj
  zagruzchik (lilo ili loadlin) o peredache parametrov yadru vo vremya
  zagruzki. lilo procedura opisana takzhe v SCSI-HOWTO, dostupnogo
  cherez ftp (user: anonymous) na sunsite.unc.edu:/pub/Linux/docs/HOWTO.)
  Standartnye bazovae adresa i sintaksis parametra lp Vy mozhete najti
  v fajle drivers/char/lp.c. Zatem Vy mozhete skazat' Y dlya PLIP
  drajvera ili, predpochtitel'nee, M. V poslednem sluchae v dokumentacii
  Documentation/networking/net-modules.txt Vy mozhete najti kak zadat'
  IRQ dlya PLIP drajvera vo vremya zagruzki modulya.
  Esli ne uvereny - otvet'te N.

        EQL (serial line load balancing) support.	CONFIG_EQUALIZER
CONFIG_EQUALIZER
  Esli Vy imeete dva soedineniya po serijnym liniyam k odnomu i tomu zhe
  komp'yuteru (eto obychno trebuet dve telefonnyh linii i po dva modema
  s oboih storon) i ispol'zuete SLIP ili PPP protokol na nih, to
  ispol'zuya etot drajver Vy mozhete zastavit' ih rabotat' kak odin
  kanal s udvoennoj skorost'yu peredachi. Estetsvenno etot rezhim dolzhen
  podderzhivat'sya s oboih storon, libo cherez EQL Linux driver, libo
  cherez Livingston Portmaster 2e. Esli Vam nuzhen etot rezhim, otvet'te
  Y i pochitajte fajl drivers/net/README.eql.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  (chto bolee predpochtitel'no) otvet'te M i pochitajte dokumentaciyu
  po modul'nym drajveram v fajle Documentation/modules.txt.

        Frame Relay (DLCI) support.	CONFIG_DLCI
CONFIG_DLCI
  |tot drajver podderzhivaet frame relay protokol, frame relay - eto
  bystryj nedorogoj sposob soedineniya k udalennomu IP provajderu
  ili sposob sozdanie sobstvennoj razvetvlennoj seti. Odna fizicheskaya
  liniya ot Vashej mashiny k lokal'nomu svichu "switch" (to est' vhod
  v set' frame ralay) mozhet soderzhat' neskol'no logicheskih soedinenij
  tochka-tochka s drugimi komp'yuterami seti frame-relay. Obshchee opisanie
  protokola Vy mozhete najti na WWW
  http://frame-relay.indiana.edu/4000/4000index.html
  Dlya ispol'zovaniya frame relay Vam neobhodimo sootvetsvuyushchee
  oborudovanie (FRAD) i programmy iz paketa net-tools, kak opisano v
  Documentation/networking/framerelay.txt.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  (chto bolee predpochtitel'no) otvet'te M i pochitajte dokumentaciyu
  po modul'nym drajveram v fajle Documentation/modules.txt.

        Max open DLCI.	CONFIG_DLCI_COUNT
CONFIG_DLCI_COUNT
  |tot parametr opredelyaet maksimal'noe chislo logicheskih soedinenij
  tochka-tochka po protokolu frame relay (kotoryj nazyvaetsya DCLI).
  Po umolchaniyu ustanavlivaetsya dostatochnoe chislo.

        Max DLCI per device.	CONFIG_DLCI_MAX
CONFIG_DLCI_MAX
  |tot parametr opredelyaet maksimal'noe chislo logicheskih soedinenij
  tochka-tochka po protokolu frame relay (kotoryj nazyvaetsya DCLI)
  na kazhdoe Vashe ustrojstvo frame relay.
  Po umolchaniyu ustanavlivaetsya dostatochnoe chislo.

        Sangoma S502A FRAD support.	CONFIG_SDLA
CONFIG_SDLA
  Otvet'te Y, esli Vy imeete Sangoma S502A, S502E ili S508 Frame
  Relay Access Devices. |to ustrojstvo podderzhivaet neskol'ko
  protokolo, no dannyj drajver na nastoyashchee vremya podderzhivaet
  tol'ko frame relay. Pochitajte fajl Documentation/framerelay.txt.
  |tot drajver mozhet byt' modul'nym (kod, kotoryj mozhet byt'
  po vashemu zhelaniyu dobavlen k uzhe rabotayushchemu yadru ili udalen).
  Esli Vy sobiraetes' ispol'zovat' drajver v modul'nom rezhime
  (chto bolee predpochtitel'no) otvet'te M i pochitajte dokumentaciyu
  po modul'nym drajveram v fajle Documentation/modules.txt.

        Sun LANCE Ethernet support.	CONFIG_SUN_LANCE
CONFIG_SUN_LANCE
  This is support for lance ethernet cards on Sun workstations such as
  the Sparcstation IPC (any Sparc with a network interface 'le0' under
  SunOS basically).

        Sun Intel Ethernet support.	CONFIG_SUN_INTEL
CONFIG_SUN_INTEL
  This is support for the intel ethernet cards on some Sun workstations
  (all those with a network interface 'ie0' under SunOS).

        Western Digital/SMC cards.	CONFIG_NET_VENDOR_SMC
CONFIG_NET_VENDOR_SMC
  Esli Vy imeete sestevuyu (ethernet) kartu etogo klassa, otvet'te
  Y i prochitajte Ethernet-HOWTO, dostupnuyu cherez ftp (user: anonymous)
  na sunsite.unc.edu:/pub/Linux/docs/HOWTO. Esli Vy planiruete
  ispol'zovat' bolee odnoj karty, prochitajte Multiple-Ethernet-mini-HOWTO,
  dostupnuyu na sunsite.unc.edu:/pub/Linux/docs/HOWTO/mini. Zamet'te, chto
  otvet na eto vopros ne podklyuchaet nikakogo drajvera k yadru, otvet Y
  daet vozmozhnost' Vam vybrat' neobhodimyj drajver.

        WD80*3 support.	CONFIG_WD80x3
CONFIG_WD80x3
  Esli Vy imeete takuyu setevuyu (ethetnet) kartu etogo tipa, otvet'te Y
  i pochtitajte Ethernet-HOWTO, dostupnuyu cherez ftp (user: anonymous) na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  |tot drajver dostupen kak modul' (kod kotoryj mozhet byt' podklyuchen
  k uzhe rabotayushchemu yadru ili udalen iz nego).
  Esli Vy hotite otkompilirovat' ego kak modul', otvet'te Y i pochitajte
  Documentation/modules.txt i Documentation/networking/net-modules.txt.
  Esli Vy planiruete ispol'zovat' bolee odnoj karty, prochitajte
  Multiple-Ethernet-mini-HOWTO, dostupnuyu na sunsite.unc.edu:
  /pub/Linux/docs/HOWTO/mini.

        SMC Ultra support.	CONFIG_ULTRA
CONFIG_ULTRA
  Esli Vy imeete takuyu setevuyu (ethetnet) kartu etogo tipa, otvet'te Y
  i pochtitajte Ethernet-HOWTO, dostupnuyu cherez ftp (user: anonymous) na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  |tot drajver dostupen kak modul' (kod kotoryj mozhet byt' podklyuchen
  k uzhe rabotayushchemu yadru ili udalen iz nego).
  Esli Vy hotite otkompilirovat' ego kak modul', otvet'te Y i pochitajte
  Documentation/modules.txt i Documentation/networking/net-modules.txt.
  Esli Vy planiruete ispol'zovat' bolee odnoj karty, prochitajte
  Multiple-Ethernet-mini-HOWTO, dostupnuyu na sunsite.unc.edu:
  /pub/Linux/docs/HOWTO/mini.
  VAZHNOE: Sushchestvuet mnogo soobshchenij o tom, chto nekotorye materinskie
  karty, imeyushchie SMC Ultra i Adaptec AHA1542 SCSI card imet' problemy
  na mnogih operacionnyh sistemah.

        SMC 9194 Support.	CONFIG_SMC9194
CONFIG_SMC9194
  |tot drajver podderzhivaet SMC9xxx Ethernet karty. Vyberite etot
  paramet, esli Vy imeete laptop s  docking station ili druguyu
  kartu na mikroshemah SMC9192/9194. Otvet'te Y, esli Vy hotite
  rabotat' s takoj kartoj i pochitajte fajl drivers/net/README.smc9
  i Ethernet-HOWTO, dostupnuyu cherez ftp (user: anonymous) na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  |tot drajver dostupen kak modul' (kod kotoryj mozhet byt' podklyuchen
  k uzhe rabotayushchemu yadru ili udalen iz nego).
  Esli Vy hotite otkompilirovat' ego kak modul', otvet'te Y i pochitajte
  Documentation/modules.txt i Documentation/networking/net-modules.txt.
  Esli Vy planiruete ispol'zovat' bolee odnoj karty, prochitajte
  Multiple-Ethernet-mini-HOWTO, dostupnuyu na sunsite.unc.edu:
  /pub/Linux/docs/HOWTO/mini.

        AMD LANCE and PCnet (AT1500 and NE2100) support.	CONFIG_LANCE
CONFIG_LANCE
  Esli Vy imeete takuyu setevuyu (ethetnet) kartu etogo tipa, otvet'te Y
  i pochtitajte Ethernet-HOWTO, dostupnuyu cherez ftp (user: anonymous) na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  Esli Vy planiruete ispol'zovat' bolee odnoj karty, prochitajte
  Multiple-Ethernet-mini-HOWTO, dostupnuyu na sunsite.unc.edu:
  /pub/Linux/docs/HOWTO/mini.

        3COM cards.	CONFIG_NET_VENDOR_3COM
CONFIG_NET_VENDOR_3COM
  Esli Vy imeete sestevuyu (ethernet) kartu etogo klassa, otvet'te
  Y i prochitajte Ethernet-HOWTO, dostupnuyu cherez ftp (user: anonymous)
  na sunsite.unc.edu:/pub/Linux/docs/HOWTO. Esli Vy planiruete
  ispol'zovat' bolee odnoj karty, prochitajte Multiple-Ethernet-mini-HOWTO,
  dostupnuyu na sunsite.unc.edu:/pub/Linux/docs/HOWTO/mini. Zamet'te, chto
  otvet na eto vopros ne podklyuchaet nikakogo drajvera k yadru, otvet Y
  daet vozmozhnost' Vam vybrat' neobhodimyj drajver.

        3c501 support.	CONFIG_EL1
CONFIG_EL1
  Esli Vy imeete takuyu setevuyu (ethetnet) kartu etogo tipa, otvet'te Y
  i pochtitajte Ethernet-HOWTO, dostupnuyu cherez ftp (user: anonymous) na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  Rassmotrite takzhe variant pokupki novoj karty, tak kak 3c501 karta
  yavlyaetsya medlennoj i ustarevshej.
  |tot drajver dostupen kak modul' (kod kotoryj mozhet byt' podklyuchen
  k uzhe rabotayushchemu yadru ili udalen iz nego).
  Esli Vy hotite otkompilirovat' ego kak modul', otvet'te Y i pochitajte
  Documentation/modules.txt i Documentation/networking/net-modules.txt.
  Esli Vy planiruete ispol'zovat' bolee odnoj karty, prochitajte
  Multiple-Ethernet-mini-HOWTO, dostupnuyu na sunsite.unc.edu:
  /pub/Linux/docs/HOWTO/mini. I popytajtes' ne ispol'zovat'
  eti karty.

        3c503 support.	CONFIG_EL2
CONFIG_EL2
  Esli Vy imeete takuyu setevuyu (ethetnet) kartu etogo tipa, otvet'te Y
  i pochtitajte Ethernet-HOWTO, dostupnuyu cherez ftp (user: anonymous) na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  |tot drajver dostupen kak modul' (kod kotoryj mozhet byt' podklyuchen
  k uzhe rabotayushchemu yadru ili udalen iz nego).
  Esli Vy hotite otkompilirovat' ego kak modul', otvet'te Y i pochitajte
  Documentation/modules.txt i Documentation/networking/net-modules.txt.
  Esli Vy planiruete ispol'zovat' bolee odnoj karty, prochitajte
  Multiple-Ethernet-mini-HOWTO, dostupnuyu na sunsite.unc.edu:
  /pub/Linux/docs/HOWTO/mini.

        3c505 support.	CONFIG_ELPLUS
CONFIG_ELPLUS
  Informaciyu po etoj serevoj (ethernet) karte Vy mozhete poluchit'
  v fajle Documentation/networking/3c505.txt.
  Esli Vy imeete takuyu setevuyu (ethetnet) kartu etogo tipa, otvet'te Y
  i pochtitajte Ethernet-HOWTO, dostupnuyu cherez ftp (user: anonymous) na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  |tot drajver dostupen kak modul' (kod kotoryj mozhet byt' podklyuchen
  k uzhe rabotayushchemu yadru ili udalen iz nego).
  Esli Vy hotite otkompilirovat' ego kak modul', otvet'te Y i pochitajte
  Documentation/modules.txt i Documentation/networking/net-modules.txt.
  Esli Vy planiruete ispol'zovat' bolee odnoj karty, prochitajte
  Multiple-Ethernet-mini-HOWTO, dostupnuyu na sunsite.unc.edu:
  /pub/Linux/docs/HOWTO/mini.

        3c507 support.	CONFIG_EL16
CONFIG_EL16
  Esli Vy imeete takuyu setevuyu (ethetnet) kartu etogo tipa, otvet'te Y
  i pochtitajte Ethernet-HOWTO, dostupnuyu cherez ftp (user: anonymous) na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  |tot drajver dostupen kak modul' (kod kotoryj mozhet byt' podklyuchen
  k uzhe rabotayushchemu yadru ili udalen iz nego).
  Esli Vy hotite otkompilirovat' ego kak modul', otvet'te Y i pochitajte
  Documentation/modules.txt i Documentation/networking/net-modules.txt.
  Esli Vy planiruete ispol'zovat' bolee odnoj karty, prochitajte
  Multiple-Ethernet-mini-HOWTO, dostupnuyu na sunsite.unc.edu:
  /pub/Linux/docs/HOWTO/mini.

        3c509/3c579 support.	CONFIG_EL3
CONFIG_EL3
  Esli Vy imeete setevuyu (ethernet) kartu serii 3Com EtherLinkIII,
  otvet'te Y i pochitajte Ethernet-HOWTO, dostupnogo cherez
  ftp (user: anonymous) na sunsite.unc.edu:/pub/Linux/docs/HOWTO.
  Esli Vy hotite otkompilirovat' ego kak modul', otvet'te Y i pochitajte
  Documentation/modules.txt i Documentation/networking/net-modules.txt.
  Esli Vy planiruete ispol'zovat' bolee odnoj karty, prochitajte
  Multiple-Ethernet-mini-HOWTO, dostupnuyu na sunsite.unc.edu:
  /pub/Linux/docs/HOWTO/mini.
  Esli Vasha karta ne rabotaet, ispol'zujte DOS setup disk dlya
  vyklyucheniya rezhima Plug&Play i ustanovite neobhodimyj tip
  konnektora.

        3c590 series (592/595/597) "Vortex" support.	CONFIG_VORTEX
CONFIG_VORTEX
  Esli Vy imeete takuyu setevuyu (ethetnet) kartu etogo tipa, otvet'te Y
  i pochtitajte Ethernet-HOWTO, dostupnuyu cherez ftp (user: anonymous) na
  sunsite.unc.edu:/pub/Linux/docs/HOWTO. Dopolnitel'nuyu informaciyu
  Vy mozhete poluchit' v fajle Documentation/networking/vortex.txt
  i v kommentariyah v nachale fajla drivers/net/3c59x.c.
  |tot drajver dostupen kak modul' (kod kotoryj mozhet byt' podklyuchen
  k uzhe rabotayushchemu yadru ili udalen iz nego).
  Esli Vy hotite otkompilirovat' ego kak modul', otvet'te Y i pochitajte
  Documentation/modules.txt i Documentation/networking/net-modules.txt.
  Esli Vy planiruete ispol'zovat' bolee odnoj karty, prochitajte
  Multiple-Ethernet-mini-HOWTO, dostu