Ocenite etot tekst:




             |ta glava specifichna dlya moego laptopa Toshiba Sattelite 5005-507,
             dlya drugih mashin aktivaciya IR mozhet byt' poproshche.
             Telefony Siemens S45 i Nokia 6510, 8310
             Linux RedHat 7.3
             Kernel version 2.4.18 (s bolee starymi yadrami dobit'sya
	     uspeha problematichno)

0.  Skoree vsego v S45 ustarelaya proshivka, s nej GPRS rabotal _tol'ko_ cherez
COM-port.   Pomogaet    ustanovka    S45_210306_UpdateTool.exe    s    sajta
www.mysiemens.com -> s45 -> device

V   Toshiba   Sattelite  5005-507  net  BIOS-nastroek,  zhelezo  konfiguritsya
programmno. IR  port  i  ISA-bridge,  na  kotorom  on  sidit,  draverami  ne
raspoznayutsya, poetomu ih predvaritel'no neobhodimo aktivirovat'.

// lspci on 5005-507 says
// 00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 05): 82801BA (0x2440)
// IR-controller:      SMC,LPC47N227,2.0,0x2e,0x3f8,0x130,3,3,128,0,1

1. Perekompilirovat' yadro, chtoby v nem uchastvuyushchie dravera byli modulyami:

##############################################################
* Character devices
M  Standart/generic serial support

* IrDA (infrared support)
M  IrDA subsystem support
M  IrLAN support
M  IrNET protocol
M  IrCOMM protocol
Y  Ultra protocol

**Infrared-port device drivers)
SIR device
M  IrTTY
M  IrPORT
FIR device
M  SMC IrCC
##############################################################

2. S pomoshch'yu ispravlennoj programmy tosh5100-smcinit (skachat' iz interneta, ispravit')
///////// Ispravit' stroku /////
  if (twobyte != 0x248c){
/////////////// na /////////////
  if ( twobyte != 0x248c && twobyte != 0x2440 ){
////////////////////////////////
  gcc -O2 -o /usr/local/sbin/tosh5100-smcinit tosh5100-smcinit.c -lpci -L/usr/lib -I/usr/include/pci

 Proverka:
 /usr/local/sbin/tosh5100-smcinit # setapim IR
 /usr/sbin/findchip               # ubezhdaemsya, chto kontroller ozhil
SMC,LPC47N227,2.0,0x2e,0x3f8,0x130,3,3,128,0,1

3. Dopisyvaem v fajl /etc/modules.conf

##############################################################
# smc-ircc Infra Red
# aktivaciya IR-porta (v Toshiba-507 on saditsya na io 0x3f8 irq 3)
# FIR ya ne ispol'zoval:  pre-install smc-ircc /usr/local/sbin/tosh5100-smcinit
pre-install serial /usr/local/sbin/tosh5100-smcinit
# zavodim COM1 na io/irq IR-porta
post-install serial /bin/setserial /dev/ttyS0 uart 16550 port 0x3F8 irq 3
alias tty-ldisc-11 irtty
alias char-major-161 ircomm-tty
alias char-major-10-187 irnet
##############################################################

4. Propisyvaem v fajl /etc/sysconfig/irda

##############################################################
IRDA=yes
DEVICE=/dev/ttyS0
DISCOVERY=yes
##############################################################

5. Zapuskaem
 /usr/local/sbin/tosh5100-smcinit
 /bin/setserial /dev/ttyS0 uart 16550 port 0x3F8 irq 3
 irattach /dev/ttyS0 -s

Finita  -  teper'  infrakrasnyj  port v rezhime SIR (do 115bod) ispol'zuem po
imeni /dev/ircomm0. Primechatel'no, chto irattch nasazhivaetsya na ttyS0,
a my pol'zuemsya devajsom /dev/ircomm0. Nichego strashnogo. Tak nado :)

Vse  ukazannye komandy pri perezagruzke budut uzhe ispolnyat'sya avtomaticheski,
vruchnuyu zapuskat' nichego ne potrebuetsya.

Proverit', chto port zhiv
 irdadump

Dlya  IR v rezhime skorostnogo FIR nuzhno podnimat' specializirovannyj FIR-draver
 modprobe smc-ircc
 (eksperimenty uspehom ne zavershilis')



Nichego  ekstraordinarnogo v nastrojkah PPP ne trebuetsya, dlya GPRS specifichny
sleduyushchie momenty (v skobkah klyuchi pppd):

 IP-adresa vydayutsya serverom (ipcp-accept-local ipcp-accept-remote noipdefault)
 DNS-servera vydaetsya serverom (usepeerdns)
(libo propisyvaetsya rukami v /etc/resolv.conf 213.87.0.1 i 213.87.1.1)
 Kompressiya zagolovkov NE ispol'zuetsya (novj nobsdcomp novjccomp nopcomp noaccomp)
 Init-stroka mobil'nika soderzhit AT+CGDCONT=1,"IP","internet.mts.ru" OK
 Ispol'zuetsya PAP-avtorizaciya (user mts i  /etc/ppp/pap-secrets)
 Login/parol' ne ispol'zuyutsya, poetomu loginnnyj skript banalen: "CONNECT"
 pppd boitsya naznachat' "svoj" default router, esli takovoj uzhe imeetsya, poetomu
 pered startom pppd default router nado udalit' rukami/programmno

1. # Gotovim fajl dlya PAP-avtorizacii s pop-serverom mts
Edinorazovo vypolnyaem komandu

echo 'mts * mts *' >> /etc/ppp/pap-secrets

2. Sozdaem komandnyj fajl pppup
==================== CUT HERE ==============================
#!/bin/sh
DIALTIMEOUT=20

# esli mobil'nik podceplen k COM1 a ne k IR, zamenit' v skripte ircomm0 na ttyS0
case "$1" in
mts0885)
  MODEM=ircomm0 SPEED=57600  MODEM_INIT=""
  IH_IP=" ipcp-accept-local ipcp-accept-remote noipdefault user mts"
  LOGSCRIPT="CONNECT"
  PHONE="0885"
  ;;
mtsgprs|*)
  MODEM=ircomm0 SPEED=115200 MODEM_INIT='AT+CGDCONT=1,\"IP\",\"internet.mts.ru\" OK'
  IH_IP=" ipcp-accept-local ipcp-accept-remote noipdefault
  debug usepeerdns user mts
  novj nobsdcomp novjccomp nopcomp noaccomp"
  LOGSCRIPT="CONNECT"
  PHONE="*99***1#"

   # *99# dlya QTEK

  ;;
esac

# pered zapuskom pppd udalyaet default router, po okonchanii - vosstanavlivaet
# Bolee korrektno bylo by vstavit' eti dejstviya v /etc/ppp/ip-up.local i /etc/ppp/ip-down.local
DR=`route -n | egrep '^0.0.0.0'| grep -v ppp | sed 's/^[^ ]*  *\([^ ]*\) .*/default gw \1/'` ;
if [ -n "$DR" ] ; then
   trap "echo route add $DR ; route add $DR ; exit"  2 3 9 15
   route delete $DR
   echo route delete $DR
   fi
##########################

##################### Pri obryve soedineniya pppd perezapuskaetsya ####################
while  true ; do
pppd \
  connect 'chat -v ABORT "NO DIALTONE" ABORT "NO CARRIER" ABORT BUSY "" '"$MODEM_INIT"' ATDP'$PHONE' '"$LOGSCRIPT"' ;' \
  crtscts defaultroute modem -detach mru 1500 \
  $NASH_IP:$IH_IP /dev/$MODEM $SPEED
sleep $DIALTIMEOUT
done
======================== END CUT HERE ==============================

Zapusk soedineniya:

pppup mtsgprs

Ostanovka: CTRL+C

Esli telefon ne otklikaetsya - vyklyuchit'/vklyuchit' ego



      Nomer telefona:
Dlya Siemens:                 *99***1#
Motorola, Nokia, Ericsson:   *99#
QTEK                     :   *99#

      MTS
user:              mts
APN:               internet.mts.ru
DNS:               213.087.0.1, 213.087.0.1 ili Avto
Header-compresion: NONE

     BeeLine
user:              beeline
APN:               internet.beeline.ru
DNS:               217.118.66.243, 217.118.66.244
Header-compresion: NONE

     Megafon
user:              gdata
APN:               internet
DNS:               Avto
Header-compresion: Yes




V Toshiba 507 (kak i v bol'shinstve novyh noutbukah) net COM-porta. Zato est'
USB i IR. Perehodnik USB->COM po stoit okolo  15$  i  ponimaetsya  FTDI-ishnym
draverom  dlya  USB, odnako net 100% garantii, chto vse eto udastsya nastroit'.
Vtoroj minus podklyucheniya mobil'nika cherez COM -  neobhodimo  imet'  dovol'no
nedeshevyj   COM-kabel'   dlya   telefona.  Tretij  minus:  COM-podklyucheniya  -
zanimaetsya raz®em  dlya  podklyucheniya  pitaniya,  a  akkumulyator  GPRS  szhiraet
dovol'no bystro (1 chas GPRS = 1 sutkam v rezhime ozhidaniya)

S drugoj storony: ne vo vseh telefonah i noutbukah est' IR-port. K nekotorym
telefonam COM-kabel' prilagaetsya v standartnoj postavke, v  otlichie  ot  IR,
telefon, visyashchij na kabele ne teryaet konnekta ot sluchajnyh smeshchenij.

 Vyvody:
 1) v noutbuke zhelatelen IR-port.
 2) v telefone zhelatelen IR-port.
 3) v telefone zhelatelen COM-kabel'.
 4) zhelatel'no, chtoby COM-kabel' i pitanie imeli razdel'nye raz®emy.
 5) polezno imet' adapter ot avtomobil'nogo prikurivatelya.
 6) lyubopyten variant s BlueTooth

Vopros  podklyucheniya  k  Linux-noutbuku  cherez  USB  ostaetsya otkrytym i zhdet
svoego issledovatelya.



Gromko ob®yavlennye mobil'nymi operatorami vysokie skorosti GPRS (do 115Kbod)
sushchestvuyut tol'ko v teorii. Real'naya skorost' peredachi dannyh 2.5-2.7Kb/sek.
Pri snizhenii kachestva signala - opuskaetsya do 0.5Kb/sek i dalee - do polnogo
nulya.

GPRS ochen' kritichen k sile signala. Pri oslablenii signala skorost' peredachi
zametno  padaet,  nachinayutsya  zaderzhki  i  obryvy  svyazi  vplot'  do  polnoj
nerabotosposobnosti dazhe pri vpolne udovletvoritel'nom urovne priema.

Vse sil'no zavisit ot modeli(proizvoditelya?) telefona. Po nekotorym otzyvam,
Motorolla derzhit svyaz' tam, gde Siemens'y i Ericsson'y uzhe ne tyanut.

Po  moemu  sobstvennomu  opytu  tam,  gde  Siemens S45 ne rabotal, ustojchivo
rabotala Nokia 6510.

 Konkretno  Siemens S45 rabotaet _tol'ko_ v usloviyah horoshego signala - hotya
by "chetyre palki" po indikatoru iz pyati vozmozhnyh (t.e. primerno do -80dBm)
 Pri "treh palkah" (-85dBm : -95dBm) soedinyaetsya, no ne rabotaet.
 Pri "dvuh palkah" (-97dBm : -109dBm) dazhe ne soedinyaetsya.

 Nokia  6510  pri  "treh  palkah"  (-85dBm  :  -95dBm)  rabotaet,  inogda  s
vremennymi vypadaniyami na 5-10 sekund,  skorost'  peredachi  450-700  bajt  v
sekundu.

 U  menya  na  dache  signal  v "3 palki", dlya raboty cherez S45 ego neobhodimo
podnyat' na 20dBm. Standartnye  odnoshtyrevye  antenny,  kotorye  prodayutsya  v
mobil'nyh  salonah, imeyut usilenie ot 5dBm(300rub) do 11dBm(700rub) - t.e. v
moem sluchae ne pomogut.
 Napravlennaya antenna v 16dB stoit okolo 80$
 Buster (podnimaet signal, provalennyj dlinnym kabelem) - 60-100$
 GSM-usilitel' na 20-25dB stoit ot 200$ do 1000$
 Repiter (usilitel' sovmeshchennyj s mini GSM-retranslyatorom) - 300$

 Vyvod:  telefon  Siemens  S45  (a  po sluham - i drugie modeli Siemens) dlya
obespecheniya GPRS v usloviyah  sredne-posredstvennogo  priema  NEPRIGODEN, ili
trebuet ustanovki antenno/usilitel'nogo hozyajstva na summu v 100-200-300$.
 A  ya  otpravlyayus'  pokupat'  Nokia (skoree vsego real'no protestirovannyj i
dokazavshij rabotosposobnost' 6510) - za 190$.


    Windows (PC), Windows CE (Pocket PC):

Make new connection: via IR-port, PPP, noheadercompression, phonenumber, dns ...
Dopolnitel'no perejti v "Svojstva modema" i zabit' v  stroku inicializacii
AT+CGDCONT=1,IP,internet.mts.ru

    PalmOS (Palm)

Bole-menee  analogichno, odnako zdes' v parametrah modema net ponyatiya "stroka
inicializacii modema", poetomu pridetsya napisat'  dialup-script,  soderzhashchij
etu stroku v nachale chata.

    EPOC-32 (Psion)

 1. V paneli upravleniya nastroit' novyj modem. V parametrah modema postavit'
"Modem type: Mobile", "Terminal Detect: NO", "Carrier Detect: NO"
 2.  V paneli "nastrojki Internet" zadat' DNS, i login
 3.  Posle  podklyucheniya  i  pervoj popytki obrashcheniya k lyubomu sajtu poyavitsya
soobshchenie "operaciyu provesti nevozmozhno".
 4. Posle etogo zapustit' programmu "GPRS Helper" ili "Mobile GPRS Update"

 GPRS Helper: http://psiloc.com/psion/eng/gprs/
 Mobile GPRS Update: http://www.mypsion.ru, dalee po ssylkam



http://www.opennet.ru/prog/sml/101.shtml
Programmy dlya upravleniya adresnoj knigoj/kalendarem/sms:

Tekstovye, s kuchej klyuchej:

scmxx-0.6.3.7-1.i386.rpm
gsmlib-1.10.tar.gz

K primeru, otsylka SMS mozhet vyglyadet' tak:
 gsmsendsms -d /dev/ircomm0 +79021234567 "Tekst SMS-soobsheniya zaklyuchennyj w kawychki"
Smena PIN u simkarty
 gsmctl -o setpw sc 1234 2345


S graficheskim interfejsom

multisync-0.72-1.i386.rpm trebuet OBEX-bibliotek, u menya ne zarabotala
xgsmlib-0.2.tar.gz        trebuet GNOME-development version 1.4, u menya ne sobralsya







Origin: http://sn00per.narod.ru/gprs/mtu_w2k.html


HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\NdisWan\Parameters\Protocols\0\ProtocolMTU
             ,
 ustanavlivaem  desyatichnoe  znachenie  MTU  men'shee  chem  1450, esli brat' po
analogii s vin98 - to
V nastrojkah soedineniya ustanavlivaem v kachestve proksi
                             proxy.mtsnet.ru i port 3128.
i sami zabudem pro
                             MTU!

                             Name: mts3.mtsnet.ru
                             Address: 213.87.0.3
                             Aliases: proxy.mtsnet.ru









Origin: http://sn00per.narod.ru/gprs/linux_gprs.html

Zapustit' GPRS pod linuksom dovol'no neslozhno. Est' massa raznyh variantov v inete, kak eto sdelat'.
Ne pretenduya na osobuyu original'nost', rasskazhu kak eto sdelal ya. YA ne stal poka paritsya s IRDA,
uchityvaya nalichie KOM-shnurka. Tak proshche i nadezhnee.
I tak.. YAdro 2.2.h, chat i pppd podrazumevayutsya ustanovlennymi. Po bol'shomu schetu osobyh otlichij ot
obychnogo modemnogo soedineniiya net. Otlichayutsya detali. I tak. Sozdaem fajly so sleduyushchim
soderzhaniem:

/etc/ppp/peers/gprs-connect-chat:

#!/bin/sh
# chat-gprs-connect
# The actual chat script:
exec chat \
TIMEOUT 5 \
ECHO ON \
ABORT '\nBUSY\r' \
ABORT '\nERROR\r' \
ABORT '\nNO ANSWER\r' \
ABORT '\nNO CARRIER\r' \
ABORT '\nNO DIALTONE\r' \
ABORT '\nRINGING\r\n\r\nRINGING\r' \
'' \rAT \
TIMEOUT 12 \
SAY "Press CTRL-C to close the connection at any stage!" \
SAY "\ndefining PDP context...\n" \
OK ATH \
OK ATE1 \
OK 'AT+CGDCONT=1,"IP","internet.mts.ru"' \
OK ATD*99***1# \
TIMEOUT 22 \
SAY "\nwaiting for connect...\n" \
CONNECT "" \
SAY "\nConnected." \
SAY "\nIf the following ppp negotiations fail,\n" \
SAY "try restarting the phone.\n"
#


/etc/ppp/peers/gprs-connect-chat:

#!/bin/sh
# chat-gprs-disconnect
exec /usr/sbin/chat -V -s -S \
ABORT "BUSY" \
ABORT "ERROR" \
ABORT "NO DIALTONE" \
SAY "\nSending break to the modem\n" \
"" "\K" \
"" "+++ATH" \
SAY "\nPDP context detached\n"
#


/etc/ppp/peers/gprs:

# Serial cable pppd options for GPRS phone
nodetach
debug
show-password
connect /etc/ppp/peers/gprs-connect-chat
disconnect /etc/ppp/peers/gprs-disconnect-chat
/dev/ttyS0 # COM1
#/dev/ttyS1 # COM2
115200
crtscts
local
noipdefault
ipcp-accept-local
defaultroute
usepeerdns
# ppp compression
novj
nobsdcomp
novjccomp
nopcomp
noaccomp
#
noauth
user "mts"


/etc/ppp/pap-secrets:

# Secrets for authentication using PAP
# client server secret IP addresses
mts * mts *



Teper' kasaemo DNS. Esli RRR stek telefona mozhet poluchat' DNS s servera GPRS
i skript /etc/ppp/ip-up mozhet pravil'no otrabatyvat'  poluchennuyu  informaciyu
ot  pppd,  to  stavim  parametr  usepeerdns  v  /etc/ppp/peers/gprs.  S etim
parametrom poluchennaya informaciya sohranyaetsya v fajle /etc/ppp/resolv.conf.

/etc/ppp/resolv.conf:

#
nameserver 213.87.0.1
nameserver 213.87.1.1
#


Esli  takoj  fint  ne  prokatyvaet  -  togda  dobav'te eti stroki v /etc/re­
solv.conf. Zaodno prover'te,  chto  /etc/host.conf  soderzhit  strochku  "order
hosts,bind".

Vrode vse... Konnektim shnurkom telefon k komportu. Kak root daem komandu pp­
pd call gprs i nablyudaem vyvod.  Ochchen' poleznaya informaciya ob  ustanovlenii
konnekta.  Mozhno  kontrolirovat',  na kakoj stadii proishodyat problemy.. Vot
naprimer, segodnya ochen' chasto ne poluchaetsya poluchit' IP adres iz  pula  MTS,
vidimo,  ves'  ischerpalsya  na  moment  konnekta.  Potom vam etot debag-musor
nadoest, i togda mozhno parametr debug zakommentirovat'. Byl eshche odin moment,
svyazannyj  s  defoltovym  marshrutom.  V  moem  sluchae  defoltovyj shlyuz byl v
lokalku pered konnktom k GPRS. YA napisal korotkij  skriptik,  kotoryj  pered
vyzovom   pppd   ubival   defoltovyj   shlyuz.    Posle   zaversheniya  konnekta
vosstanavlival lokal'nyj defoltovyj shlyuz v skripte /etc/ppp/ip-down.local

Vot i vse..potratil polchasa na pol'zu narodu. Prodolzhaem sledit' za bredom v
forume i vylavlivat' interesnye mysli i idei..Kak  nadoeli  eti  halyavshchiki..
Vse voprosy v pochtu, hotya ya ne uveren, chto budet vremya otvechat'.

1.03.03







Origin: http://ruslandh.narod.ru/GPRS/ch27.html

M.Bykov, I.Sinelobov, S.Skorohodov
Snachala nastroim infrakrasnyj port, dlya chego ustanovim paket irda-utils:

apt-get install irda-utils

Spisok ustanovlennyh v sostave paketa programm vy mozhete poluchit', vvedya sleduyushchuyu komandu:

rpm -ql irda-utils

Teper' u nas est' irdadump, irattach i dokumentaciya k nim. Man-stranicy s dokumentaciej sushchestvuyut
otdel'no ot paketa: http://mobilix.org/software/irda/

Teper', dlya togo chtoby opredelit' vash IR-chipset i sootvetstvuyushchij emu modul', vvedite komandu lspci,
predvaritel'no ubedivshis' v tom, chto infrakrasnyj port vklyuchen v BIOS. V vyvode konsoli v sluchae s
ukazannym vyshe noutbukom vy pomimo drugoj informacii uvidite sleduyushchee:

    00:09.0 Communication controller: Toshiba America Info Systems
    FIR Port (rev 23)


FIR (Fast Infra-Red) oznachaet horoshij chipset, kotoromu sootvetstvuet ustrojstvo /dev/ircomm0. V nekotoryh
modelyah noutbukov Toshiba stoyat chipsety SIR (Serial Infra-Red), kotorye "pritvoryayutsya" posledovatel'nym
portom /dev/ttyS0 i obespechivayut skorost' soedineniya do 115 Kb/sek, a FIR- do 4 Mb.

Vyvod komandy lspcidrake da£t nazvanie modulya:

    toshoboe    : Toshiba FIR Port


V LINUX-IFRARED govoritsya, chto v /etc/modules.conf dolzhno byt'

    alias tty-ldisc-11 irtty
    alias char-major-161 ircomm-tty


Dobavim neobhodimye stroki i zagruzim nuzhnye moduli:

$ modprobe toshoboe

$ service irda start

Proverim:

$ service irda status

  irattach (pid XXX) is running...


Zamechanie

Komandu irattach ircomm0 -s 1, kotoraya vam vstretitsya v dokumentacii, davat' ne nuzhno- vs£ sdelaet service
irda start.

Aktiviziruem IR na sotovom telefone, "pristroim" telefon k IR-okoshku noutbuka, i, chtoby ubedit'sya v tom,
chto on opredelilsya, posledovatel'no vvodim sleduyushchie komandy i smotrim na ih vyvod:

    # cat /proc/net/irda/discovery - pishet, uvidel Motorolu.

    # irdadump (daet potok, no posle starta servisa irda ne vse
    stroki odinakovye, yavno kakaya-to zhizn').

    # ifconfig pokazyvaet irda0 i lo.

    # dip -t
    >port ircomm0
    >term


v terminale- AT i vvod, na chto telefon chestno otvechaet OK. Mozhno pozvonit' ATDXXXXX na gorodskoj
telefon i uslyshat' pisk.

Teper' samoe slozhnoe- zapustit' ppp. Vnosim ispravleniya v skripty iz paketa gprs-ppp-scripts.tgz (privozhu
tol'ko otlichiya):

V fajl /etc/ppp/pap-secrets, delaya probel nazhatiem na klavishu Tab, vnosim sleduyushchuyu zapis':

    mts *       mts
    beeline     *       beeline


V fajl /etc/ppp/peers/gprs-moto:

    name mts


libo

    name beeline


V fajl /etc/ppp/gprs-options:

    debug - potom polezno vyklyuchit'


V fajl /etc/ppp/chatscripts/gprs-moto-connect-chat zapishem:


    OK  'AT+CGDCONT=1,"IP","internet.mts.ru"'
    (OK         'AT+CGDCONT=1,"IP","internet.beeline.ru"')


Teper' vved£m komandu pppd call gprs-moto i prochitaem e£ vyvod:

    ....

    Script /etc/ppp/ip-up started (pid xxx)


Esli vy uvideli eti stroki, znachit est' local IP, i my v seti.

Zamechanie

Esli  poyavitsya  soobshchenie  "not replacing existing default route to eth0", a
eto oznachaet, chto # ifconfig pokazyvaet eth0, irda0, i lo a  #  netstat  -nr
pokazyvaet  "defoltnyj"  gateway,  propisannyj  dlya  vashej setevoj kartochki,
prover'te opciyu default gateway v fajle  /etc/ppp/gprs-options  (ili  prosto
dostan'te pcmcia-kartu).

Nastrojki  telefonov  smotrite  na  sajtah  kompanij:  obychno  nastrojki  po
umolchaniyu rabotayut, no inogda byvaet neobhodimo vklyuchit' i vyklyuchit' telefon
posle nastrojki ili aktivizacii servisa.

Paket  gprs-ppp-scripts.tgz nuzhno zagruzit' so stranicy PPP over GPRS from a
UNIX machine.

Literatura

UniX and (Cellular) Phones. http://mobilix.org/phones_linux.html.

Linux Infrared HOWTO. http://mobilix.org/Infrared-HOWTO/Infrared-HOWTO.html.

LINUX GPRS HOWTO. http://turtiainen.dna.fi/GPRS-HOWTO.

Linux on the Road. http://mobilix.org/Mobile-Guide.db/Mobile-Guide.html.

something like "/usr/sbin/irattach /dev/ttyS1 -s 1".



http://linux.toshiba-dme.co.jp/linux/eng/faq2/comm/02215.htm

05/21/2002
Hi,

I am currently trying to get the IrDA stuff working in my SatellitePro
6000, but with no success so far.

I already read, that it's some SMC hardware contained in the PCI-to-ISA
bridge (M1533) of the ALi chipset. Which makes me wondern, if I should
go for the ali-ircc or smc-ircc module of my current 2.4.19-pre7 kernel.

But I think, before I try to load a module, findchip (part of the
irda-common package in Debian Woody) should mention the related
hardware.

According to
http://www.pasta.cs.uit.no/pipermail/linux-irda/2001-October/003262.html
there is the problem of activating the SMC chip first. The tools setpci
and setsmc haven't changed the behaviour on my SatellitePro 6000.
On the other hand it's quite unlikely, that setpci/setsmc written for a
SP4600 will also work on a SP6000, even if the IrDA-component seems to
be identical.

Any ideas about further approaches to this problem?
[tlinux-users:02306]       05/31/2002
Hi,

I solved the problem in the meanwhile:
- The SMC hardware is using dma=1, irq=10, firbase=0x130, sirbase=0x2e8.

- Use Daniele Peri's tool to activate the IrDA stuff, which is not done
automatically by the BIOS:

http://www.csai.unipa.it/peri/toshsat1800-irdasetup/

I am using a pre-install entry in my modules.conf:
options smc-ircc ircc_dma=1 ircc_irq=10 ircc_sir=0x2e8 ircc_fir=0x130
pre-install smc-ircc /usr/local/bin/toshsat1800-irdasetup --dma=1 --irq=10 -
-firbase=0x130 --sirbase=0x2e8

- Take care to exclude the ioports for smc-ircc in the pcmcia
configuration (file /etc/pcmcia/config.opts on my Debian Woody box):
exclude port 0x130-0x137, port 0x2e8-0x2ef
In my case the 0x130 port would otherwise be used by orinoco_cs.







Askey 1456VQL4(INT) Lucent Scorpio

Download slmdm-2.7.9.tar.gz (resp. the newer version) from the following
webpage and copy it into the /tmp folder:
http://linmodems.technion.ac.il/packages/smartlink/
slmdm-2.7.9.tar.gz

Install all necessary developer packages gcc, rpmbuild, kernel sources ...

Check if the "linux" link points to the kernel sources to avoid compilation
problems:
cd /usr/src
ls -l
Create "linux" link if it does not exist
ln -s linux-2.4... linux

Build rpm packages
cd /tmp
rpm -ta slmdm-2.7.9.tar.gz for SuSE
rpmbuild -ta slmdm-2.7.9.tar.gz for RedHat
(for older RedHat versions use: "rpm -ta slmdm-2.7.9.tar.gz")

Install new rpm-packages
cd /usr/src/packages/RPMS/i386/ for SuSE
cd /usr/src/redhat/RPMS/i386/ for RedHat
rpm -Uhv slmdm-2.7.9-0.i386.rpm
rpm -Uhv slmdm-amr-2.7.9-0.i386.rpm

Add the following line into /etc/modules.conf. Replace "GERMANY" with your
country.
Default setting is USA.
Look into the README for more details if necessary. See last lines.
options slmdm country=GERMANY
http://www.angelfire.com/linux/notebook/toshiba/satellite3000514.html


You can add the following lines into the /etc/rc.d/boot.local (SuSE),
/etc/rc.d/rc.local (RedHat)
to load modules at every bootup
(execute this commands also now in the console to load the modules
immediately for the following tests)
/sbin/insmod slmdm
/sbin/insmod slamrmo
/sbin/insmod slfax
(Your system should load this modules automatically at bootup.)

Stop for the test the network to exclude routing problems
rcnetwork stop for SuSE
service network stop for Red Hat
or
ifconfig eth0 down
ifconfig eth1 down ...

Start KDE -> open a Terminal and type kppp& or start it by menu.
Select "Device"-tab and set Modem Device: /dev/modem.
Select "Modem"-tab ->"Query Modem" if answer is ok click on "Modem
Commands".
Insert in the "Dial String:" Field "ATX3DT" if you are using your own
Telephone System (PBX).
Create your Dialup profile and dial into the internet.

For all other Linux distributions or additional information look into the
README file:
cd /tmp
tar -xvzf slmdm-2.7.9.tar.gz
cd slmdm-2.7.9
less README

Maybe it will work ... sometimes.
But it is not reliable!
I am using my PCMCIA Modem further on.



1. Vklyuchit' v yadre podderzhku Serial over USB

 Support for USB
     V sekcii USB Serial Converter support->
        USB Serial Converter support
        USB Generic Serial Driver
        USB Prolific 2303 Single Port Serial Driver(?)

I ispol'zovat' devajs /dev/usb/tts/0



http://www.hanscees.com/bluezhowto.html
http://bluez.sourceforge.net

Dialup podklyuchenie Linux PC cherez Bluetooth & GPRS
http://www.smartweb.ru/news.php?act=c&page=27&cat=2&scat=6

                                                            ssylki k stat'e:




http://www.linmodems.org/
a tam - kak povezet



Kopiruete fajl Z:\System\Data\irda.esk v C:\System\Data\irda.esk
dopisyvaete v konec fajla strochku "irMinLinkTurnaroundTime= 1".

 irda.esk vyglyadit tak:
[sockman]
protocols= irmux,tinytp

[irmux]
filename= irda.prt
index= 1

[tinytp]
filename= irda.prt
index= 2
irPod= jeteye7401
irBaud= 115200
irPhysicalComPort= 3
irLinkDisconnectTime= 20
irSupportedBauds= 319
irWindowSize= 1
irMinLinkTurnaroundTime= 1



Tochka dostupa (APN): internet.beeline.ru
Imya pol'zovatelya (User id): beeline
Parol' (Password): beeline
Zapros parolya (Password reqest): Otkl (Off)
Razreshennye vyzovy (Allow calls): avtomaticheski
(Auto)
IP-adres (IP address): ostavit' pustym
Adres DNS (DNS): ostavit' pustym
Dopolnitel'nye nastrojki (Advan.settings):

Autentifikaciya (Authentication): obychnaya (normal)
Szhatie dannyh (Data compr): Otkl (Off)
Szhatie zagolovkov (Header compr): Otkl (Off)
Kachestvo obsluzhivaniya (Quality of serv): vo vseh
podpunktah ustanovite
?po umolchaniyu? (Subscribed)


*99***1#
AT+CGDCONT=1,"IP","internet.beeline.ru"
bez kompressii zagolovkov




Last-modified: Tue, 01 Aug 2006 05:57:57 GMT
Ocenite etot tekst: